Happymodel Mobula 6 BNF Frsky Brushless Whoop BNF
This is the Happymodel Mobula 6 BNF version, this 65mm brushless whoop from Happymodel weighs in at just 20g.
The Mobula 6 is a heap of fun in a true Tiny Whoop fashion. It features the Crazybee F4 Lite flight controller (4x5A ESC) that includes either a built in Frsky or Flysky receiver. For your viewing pleasure 🙂 HappyModel designed the Mobula 6 with a great lightweight Runcam camera, the Runcam nano 3.
This is the regular edition with the SE0802 KV19000 brushless motors.
Highlights:
- Crazybee F4 Lite Flight Controller with MPU6000 (1S lipo support)
- The lightest tiny whoop at 20g
- Strong injection moulded canopy
- Runcam Nano 3 FPV camera
- Includes batteries and charger
- Brand Name: Happymodel
- Model: Mobula6
- Item Name: 65mm Crazybee F4 Lite 1S Brushless Whoop FPV Racing Drone BNF
- Optional Version: Frsky Receiver ( Compatible with ACCST D8/D16, Recommend D8 mode)
Flysky Receiver ( Compatible with AFHDS and AFHDS-2A Flysky transmitter) - Drone Wheelbase: 65mm
- Size: 80x80x37mm
- Weight: 20g
Your Package includes:
Item Name | Qty |
Mobula6 1S 65mm whoop Drone Frame | 1 |
SPI Receiver Option1: Crazybee F4 Lite FC built-in Frsky SPI D8 RX | 1 |
SPI Receiver Option2: Crazybee F4 Lite FC built-in Flysky SPI RX | |
SE0802 KV19000 or KV25000 brushless motor | 4 |
Gemfan 1219-3 Propellers(4cw+4ccw) | 1 |
Runcam Nano3 1/3 CMOS 800TVL camera | 1 |
5.8G 25mw 40ch vtx (Flight controller built-in) | 1 |
1S 250mah 30C LiHV Battery | 4 |
1S Lipo/LIHV USB Charger | 1 |
Propeller disassemble tool | 1 |
Detailed information:
Spare parts specifications:
Motor | Mode: SE0802 19000KV or KV25000 Configu-ration:9N12P Stator Diamter:8mm Stator Length:2mm Shaft Diameter:Φ1mm Motor Dimension(Dia.*Len):Φ10.5mm*14.9mm Weight(g):1.9g No.of Cells(Lipo):1S only |
Propellers | Gemfan 1219-3 Center Thickness:5mm Prop Disk Diameter:31mm Center Hole Inner diameter:1.0mm Weight:0.28g |
Flight controller | (Frsky SPI RX version) CRAZYBEE F4 Lite Frsky version Firmware target: CrazybeeF4FR (Flysky SPI RX version) CRAZYBEE F4 Lite Flysky version Firmware target: CrazybeeF4FS MCU:STM32F411CEU6 (100MHZ, 512K FLASH) Sensor: MPU-6000(SPI connection) Board size: 28.5 * 28.5MM Power supply: 1S battery input (DC 2.9V-4.35V) Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready Built-in Betaflight OSD(SPI Control) Built-in 5.8G VTX Built-in SPI Frsky/Flysky receiver Built-in 5V 1A BEC Built-in voltage detection |
Onboard 4in1 ESC | MCU upgraded to EFM8BB21 Power supply: 1S LiPo/LiPo HVCurrent: 5A continuous peak 6A (3 seconds) Support BLHeliSuite programmable Factory firmware: O_H_5_REV16_7.HEX Default protocol: DSHOT600 |
Onboard Frsky SPI D8 receiver Version | SPI BUS receiver Frsky D8 compatible Compatible Non EU transmitter D8 modelChannels: 8ch Failsafe support No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m |
Onboard Flysky SPI receiver Version | SPI BUS receiver Protocol: AFHDS and AFHDS-2A Switchable Channels: 8ch(AFHDS) or 14ch(AFHDS-2A) No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m Failsafe support |
Onboard 5.8g VTX | Output power: 25mw Frequency: 40CH Input voltage: 3.3V 5.5V Current consumption: 300mA(type) Frequency: 5.8GHz 5bands 40 channels With Race bandSmartaudio ready |
Runcam Nano3 | Model: RunCam Nano 3 Image Sensor: 1/3″ CMOS Horizontal Resolution: 800TVL Lens : 2.1mm(M8) FOV 160° Signal System: NTSC S/N Ratio: >50dBElectronic Shutter Speed: Auto Auto Gain Control (AGC): Auto Min. Illumination: 0.01Lux@1.2F D-WDR: Auto Day/Night: Color Power:DC 3-5.5V Current: 110mA@5V 120mA@3.3V Housing Material: ABS Net Weight: 1.2g Dimensions: L14mm*W14mm*H9mm |
Lipo Battery | Capacity:250mAh Voltage:3.8v Continuous Discharge Rate: 30C Size: 57mmx12mmx7mm Weight: 8gConnector: PH2.0 |
More Information
Special Note : It is possible for the Mobula6 to lose bind and betaflight config if the battery is allowed to run low – however this can be easily resolved to get back in the air again.
Please Read.
Reviews
There are no reviews yet.